Can the RTX 3080 10 GB run Wan 2.2 TI2V 5B?
Yes, but only just: Q8_0 leaves 0.8 GB free on the RTX 3080 10 GB.
Q8_0 (5.4 GB) fits with only 0.8 GB to spare (about 9.2 GB of 10 GB).
Using Kijai's WanVideoWrapper instead of the native nodes? Its WanVideo BlockSwap node keeps part of the model in system RAM. To run the 16-bit file (10.0 GB) on RTX 3080 10 GB, start with blocks_to_swap ≈ 13 (of 30). Each block is about 0.3 GB; raise the number if you still run out of memory, lower it for speed. estimate WanVideoWrapper →
01What to download
| Part | File | Folder | Size | |
|---|---|---|---|---|
| Model | Wan2.2-TI2V-5B-Q8_0.gguf Q8_0 · QuantStack/Wan2.2-TI2V-5B-GGUF | models/unet | 5.4 GB | Download → |
| Text encoder | umt5_xxl_fp8_e4m3fn_scaled.safetensors UMT5-XXL FP8 (scaled) · Comfy-Org/Wan_2.1_ComfyUI_repackaged | models/text_encoders | 6.7 GB | Download → |
| VAE | wan2.2_vae.safetensors Wan 2.2 VAE · Comfy-Org/Wan_2.2_ComfyUI_Repackaged | models/vae | 1.4 GB | Download → |
| Total download · keep about the same free on disk | 13.5 GB | |||
Alternatives: UMT5-XXL FP16 (11.4 GB). Sizes from Hugging Face, 2026-10-01.
Free ComfyUI workflow, tested on my RTX 5060 Ti: text to video workflow (.json). Drag the file into ComfyUI. All workflows →
02Every Wan 2.2 5B file on 10 GB
| File | Size | Needed | On this card | Quality | Download |
|---|---|---|---|---|---|
| 16-bit SAFETENSORS · Comfy-Org | 10.0 GB | 13.8 GB | 3.8 GB too big | the original weights | Hugging Face → |
| Q8_0 ← GGUF · QuantStack | 5.4 GB | 9.2 GB | fits · 0.8 GB spare | practically identical to the original | Hugging Face → |
| Q6_K GGUF · QuantStack | 4.2 GB | 8.0 GB | fits · 2.0 GB spare | very close to the original | Hugging Face → |
| Q5_K_M GGUF · QuantStack | 3.8 GB | 7.6 GB | fits · 2.4 GB spare | close; small differences in fine detail | Hugging Face → |
| Q4_K_M GGUF · QuantStack | 3.4 GB | 7.2 GB | fits · 2.8 GB spare | good; some loss in fine detail and text | Hugging Face → |
| Q3_K_M GGUF · QuantStack | 2.5 GB | 6.3 GB | fits · 3.7 GB spare | noticeable loss of detail | Hugging Face → |
| Q2_K GGUF · QuantStack | 1.9 GB | 5.7 GB | fits · 4.3 GB spare | heavy loss; a last resort | Hugging Face → |
“Needed” adds 3 GB of working memory for Wan 2.2 5B and a 0.8 GB reserve. Sizes 2026-10-01.
03Measured and reported results
Nobody has sent measured numbers for this pair yet. If you run Wan 2.2 5B on a RTX 3080 10 GB, send your time per image and peak VRAM and it will appear here, credited.
04About the RTX 3080 10 GB
The RTX 3080 10 GB (Ampere) has no FP8 compute. FP8 files still load and save memory, but ComfyUI converts them back before the maths, so there is no speed gain - Q8_0 GGUF is the closer-to-original 8-bit choice. ComfyUI can compute INT8 files natively on NVIDIA, which is worth a try where a model offers one.
10 GB GDDR6X · 320-bit · 760 GB/s · Ampere. Everything that runs on it →
05Questions
How much VRAM does Wan 2.2 5B need?
Around 5.7 GB with the smallest file (Q2_K) and 9.2 GB with an 8-bit file (Q8_0). The full 16-bit file needs about 13.8 GB.
Which Wan 2.2 5B file should I download for the RTX 3080 10 GB?
Q8_0 (5.4 GB) from QuantStack/Wan2.2-TI2V-5B-GGUF. Load it with Unet Loader (GGUF) from the ComfyUI-GGUF node pack.
How much do I need to download for Wan 2.2 5B on the RTX 3080 10 GB?
13.5 GB: Wan2.2-TI2V-5B-Q8_0.gguf, umt5_xxl_fp8_e4m3fn_scaled.safetensors, wan2.2_vae.safetensors.